5 Basic chkconfig Command Examples in Linux

This is our ongoing Linux command series where we are going to review how we can use chkconfig command efficiently with it’s available parameters. The Chkconfig command tool allows to configure services start and stop automatically in the /etc/rd.d/init.d scripts through command line. Let’s see some examples.

chkconfig command examples
5 chkconfig command examples

1. List All Services

Using ‘–list‘ parameter will displayed all services and their current start-up status in each run-level configuration.

[root@tecmint ~]# chkconfig --list

NetworkManager  0:off   1:off   2:on    3:on    4:on    5:on    6:off
abrt-ccpp       0:off   1:off   2:off   3:on    4:off   5:on    6:off
abrt-oops       0:off   1:off   2:off   3:on    4:off   5:on    6:off
...

2. Check Status of Specific Service

Below command shows startup configuration for a particular service. It’s showing HTTP services are turned off in all run levels.

[root@tecmint ~]# chkconfig --list | grep httpd
httpd           0:off   1:off   2:off   3:off   4:off   5:off   6:off

3. How Do I Start a Particular Service on Run Levels

The following ‘chkconfig‘ command shows how we can start HTTP services only on run level 3 and 5 with ‘–level‘ parameter. First command starts httpd services on run level 3 and 5 and second command verifies the status of httpd services running on run level.

[root@tecmint ~]# chkconfig --level 35 httpd on
[root@tecmint ~]# chkconfig --list | grep httpd
httpd           0:off   1:off   2:off   3:on    4:off   5:on    6:off

4. How to Check Which Services are On/Off

The following command will display all the services which are On and Off in specific run level 5.

[root@tecmint ~]# chkconfig --list | grep 5:on
NetworkManager  0:off   1:off   2:on    3:on    4:on    5:on    6:off
abrt-ccpp       0:off   1:off   2:off   3:on    4:off   5:on    6:off
abrt-oops       0:off   1:off   2:off   3:on    4:off   5:on    6:off
abrtd           0:off   1:off   2:off   3:on    4:off   5:on    6:off
acpid           0:off   1:off   2:on    3:on    4:on    5:on    6:off
...
[root@tecmint ~]# chkconfig --list | grep 5:off
dnsmasq         0:off   1:off   2:off   3:off   4:off   5:off   6:off
dovecot         0:off   1:off   2:off   3:off   4:off   5:off   6:off
firstboot       0:off   1:off   2:off   3:off   4:off   5:off   6:off
kdump           0:off   1:off   2:off   3:off   4:off   5:off   6:off
mysqld          0:off   1:off   2:off   3:off   4:off   5:off   6:off
netconsole      0:off   1:off   2:off   3:off   4:off   5:off   6:off
nfs             0:off   1:off   2:off   3:off   4:off   5:off   6:off
...

5. How Do I Stop a Particular Service on Run Levels

The following command will turned Off a service called postfix for a just single run level. Similarly, we can turn Off a particular service in multiple run levels in one go as shown under.

[root@tecmint ~]# chkconfig --level 3 postfix off
[root@tecmint ~]# chkconfig --level 2345 postfix off

As we all know, there are seven run levels are available on Linux Operating System. We’ll cover the significant of different run levels and booting sequence in details in our upcoming article. So, please stay tuned.

If you read this far, tweet to the author to show them you care. Tweet a thanks
Ravi Saive
I am an experienced GNU/Linux expert and a full-stack software developer with over a decade in the field of Linux and Open Source technologies

Each tutorial at TecMint is created by a team of experienced Linux system administrators so that it meets our high-quality standards.

Join the TecMint Weekly Newsletter (More Than 156,129 Linux Enthusiasts Have Subscribed)
Was this article helpful? Please add a comment or buy me a coffee to show your appreciation.

12 thoughts on “5 Basic chkconfig Command Examples in Linux”

  1. Guys, I have not tested this command on my Ubuntu 20.04.2 so excuse me. I see this article is a bit old.

    I have been using systemctl now as SystemD replaced SystemV. Is still valid? Well, the easiest way to find out is to go to the terminal but my CPU fan is not cleaned lately and my laptop overheated so it’s off now.

    And BTW I wanted to “buy you a coffee” but Stripe ( do not have a PayPal account ) refuses payments from the EU to India.

    I did not try on your site but on another one more than 5 times.

    Reply
  2. Is the run level 0 and 6 require for service?

    Ex: chkconfig –level 02356 servicename on

    May I know the reason for 0 and 6 levels to assign the particular service.

    Thanks & Regards,
    Nagarajan J

    Reply
  3. Sir, I need to know the way to find out the service name and daemon name for a particular package. Example for samba package alone, it has to show the service name smb and daemon name smbd.

    Thanks in advance

    Reply
  4. Current Introduction typo to be corrected for directory path of RC scripts; /etc/rd.d/init.d

    The Chkconfig command tool allows to configure services start and stop automatically in the /etc/rd.d/init.d scripts through command line. Let’s see some examples.

    Corrected directory path of RC scripts; /etc/rc.d/init.d

    Reply

Got something to say? Join the discussion.

Thank you for taking the time to share your thoughts with us. We appreciate your decision to leave a comment and value your contribution to the discussion. It's important to note that we moderate all comments in accordance with our comment policy to ensure a respectful and constructive conversation.

Rest assured that your email address will remain private and will not be published or shared with anyone. We prioritize the privacy and security of our users.